Miscellaneous Propeller Tooling

ANTI-THEFT SECURITY SYSTEMS

propcopb.gif (10010 bytes) THE PROP COP
The Prop Cop is specifically designed to protect High Performance Propellers, but can be used on standard units as well as counter rotating propellers. It is a precision made, superior quality product that protects against theft by obstructing access to the propeller nut. It can be used during transit, on a boat lift, or in the water.
The adapter is specially coated for wear and isolation of electrolysis, and is precision machined -- running concentric with the propeller shaft -- spinning freely during operation of your boat.
Designed to fit most propellers it is simple to install.

1. PART NUMBER 01 Evinrude & Johnson outboards: 150 HP to 3.6 and 1985; 120 to King Cobra and OMC 2.5 liter out drive 3/4" threaded through the hub exhaust standard propeller, and Turbo Raker II.
2. PART NUMBER 01A Evinrude & Johnson hole shot.
3. PART NUMBER 02 Same power as above, 3/4" thread through the hub exhaust, preformance type propeller, Cleaver and Laser style.
4. PART NUMBER 03   Same as above 3/4" thread over the hub exhaust Chopper style with built in spline washer type propeller with lock tabs. (Mercury style use M3, Cotter Pin style use 03).
5. PART NUMBER 04 Evinrude & Johnson: 60 to 140 HP, except 1985; 110 to 140 HP (with large gearcase) standard propeller through the hub exhaust 5/8" thread (also Cobra).
6. PART NUMBER M1 Mariner & Mercury Outboards: 75 HP to 3.4 liter, Mercruiser 120 to 260 HP and 330 to 370 TRS drives with lock tabs, 3/4" thread, through the hub exhaust, standard propeller.
7. PART NUMBER M2 Same power as above, 3/4" thread with lock tab, through the hub exhaust performance propeller. Cleaver, Laser, and Mirage style.
8. PART NUMBER M3 Same power as above, 3/4" thread with built-in spline washer lock tabs. Over the hub exhaust, performance propeller, Cleaver and Chopper style. Also Turbo Protester and Predator propeller. (recessed hub, see below).
9. PART NUMBER Y1 Yamaha outboard: 115 HP to V6 18MM thread, standard propeller through the hub exhaust. Also Suzuki 75 to
200 HP standard propeller.
10. PART NUMBER Y2 Same power as above 18MM thread, performance propeller, over the hub exhaust using Chopper or Cleaver style,
3 or 4 bladed Protester, Predator or Turbo propeller with built-in spline washer and lock tabs, Mercury style.
11. PART NUMBER Y3 Yamaha outboard: 50 to 90 HP, 16MM thread, standard propeller through the hub exhaust.
12. PART NUMBER F1   Force outboards: 65 to 125 HP, 5/8" thread.
13. PART NUMBER F2 Force outboards: 150 HP, 3/4" thread.
14. PART NUMBER F3   Force outboards: Mercury style lock tabs. See M1 and M2.
*Note: All 3/4" thread, with solid hub and flat washer are available on special order. All 3/4" thread recessed hub through the hub exhaust can use
02 or M2.

RETAIL - $56.00

A1 PROPS - $48.00

THE PROPATECTOR
Our economy model theft deterent retains many of the quality features of the prop cop. Aluminum adaptor is anodized to inhibit corrosion. Like the
prop cop, it can be used on counter rotating propellers and can be keyed alike for twin engines.

1. PART NUMBER MPT1 Fits: Mariner & Mercury 3/4" thread, 75 HP to 3.4 liter outboards; Mercruiser 120 to 260 HP and 330 to 370 TRS standard prop.
2. PART NUMBER OPT1 Fits: Evinrude & Johnson outboards 150 HP to 3.6 liter; 3/4" thread Cobra (with large lower gearcase) and King Cobra. Standard propeller.
3. PART NUMBER OPT2 Fits: Evinrude & Johnson outboards; 60 to 140 HP, except 1985; 110 to 140 HP (with large gearcase) standard prop through the hub exhaust, 5/8" thread (also Cobra) standard propeller.
4. PART NUMBER FPT1 Fits: Force outboards; 65 to 125 HP, 5/8" thread. Standard propeller.
5. PART NUMBER FPT2 Fits Force outboards; 150 HP, 3/4" thread. Standard propeller.
6. PART NUMBER FPT3 Fits: Force outboards; Mercury style lock tabs. Standard propeller.
7. PART NUMBER YPT1 Fits Yamaha outboards; 115 HP to V6 18MM thread, standard propeller through the hub exhaust. Also Suzuki 75 to 200 HP standard propeller.

RETAIL - $56.00

A1 PRICE - $48.00

OUTBOARD LOK ADAPTER
Have around the clock security at all times with the outboard lock adaptor. Fits most outboards. Adaptor and locking bar crafter of 18-8 stainless steel, locking nut is heat-treated stainless steel. The locking bar prohibits access to the hex head of the bolt so it can not be turned. The adapter is inserted over the threaded end of the bolt, and is secured by the "Cam Lok Nut". The Cam Lok Nut comes with a coded key and registration card.

PART NUMBER
OBCL1 (FITS: 1/2" COARSE THREAD)
OBCL2 (FITS: 3/8" COARSE THREAD)

RETAIL - $70.00

A1 PRICE - $60.00

STERN GUARD
For Mercruisers only.
Your stern drive is an easy, and profitable target for thieves. It can be removed from your boat in minutes.
You can protect this valuable piece of equipment in seconds with Anti-Theft Lock Adapters. The adapters lock to the
stern after the removal of a nut and washer. Simply insert the adapter on the stud -- with the flat side to the outdrive. The
new nut (supplied) is put in place and tightened, and the adapter is then locked in place.
The adapter housing and special nut are crafted from non corrosive 18-8 stainless steel, "O" rings, both front and rear, to assure a water tight seal. The adapter comes with a special High Security Locking System, including a key as unique as the combination of a bank vault -- with hundreds of millions of combinations. Can be keyed alike.

PART NUMBER
SSSW    (FITS: 120 TO 260 HP MERCRUISER ALSO ALPHA DRIVES)
RETAIL - $70.00                   A1 PRICE - $60.00
TSSW    (FITS: 330 TO 370 HP TRS DRIVES)
RETAIL - $80.00                   A1 PRICE - $68.00
BSSW    (FITS: BRAVO I DRIVES AND 1991 ALPHA)
RETAIL - $70.00                   A1 PRICE - $60.00

CAM LOCKS camloka.gif (19097 bytes)

Our superior sterndrive locking system enables you to lock upper and lower outdrive units. Can be used in water, during storage, or transit. Due to its design, it is a superior theft deterrent and is the finest available on the market today. Our top
of the line locks have one million more lock combinations than all our competitors combined. The locking nut is heat treated stainless steel and the unit takes only minutes to install. Keyed alike for twin installations.

1. PART NUMBER CLU            Fits: Upper unit, 120 to 260 HP Mercruiser and Alpha.
RETAIL - $42.00                   A1 PRICE - $36.00
2. PART NUMBER CLUC        Fits: Upper unit for Cobra only.
RETAIL - $42.00                   A1 PRICE - $36.00
3. PART NUMBER CLL            Fits: Lower unit forMercruiser and Alpha drives, 120 to 260 HP.
RETAIL - $38.00                   A1 PRICE - $33.00
4. PART NUMBER CLUL        Fits: Upper and lower units for Mercruiser 120 to 260 HP.
RETAIL - $58.00                   A1 PRICE - $50.00
5. PART NUMBER CLUV         Fits: Upper unit for Volvo only.
RETAIL - $42.00                   A1 PRICE - $36.00

For further information contact us@
ADVANTAGE PROPELLER DISCOUNT CENTER
P.O. Box 677
Washington, Michigan 48094-0677
1-888-757-PROP (1-888-757-7767)
CLICK TO E-MAIL advantage677@sbcglobal.net

OIL/FUEL FILTER WRENCH This handy wrench removes screw-on type marine water separator fuel filters and standard screw-on oil filters. Fits most standard sizes. Tough - forged stainless steel.
PART NUMBER	RETAIL	A1 PRICE
SMI 01117	$45.95	$35.00

ENGINE ALIGNMENT TOOL For use with: Mercruiser drives 1, 1A, 1B, and 1C. (1964 to date/all #1 drives) all OMC Cobra sterndrives.
PART NUMBER	OEM NUMBER	RETAIL	A1 PRICE
GLM 90050	91 57797A3	$103.00	$78.00

DRIVEN GEAR SHIMMING TOOL Measures upper driven gear clearance on MC-I, R-MR, and Alpha One; and Alpha One, Gen Two drive units.
PART NUMBER	OEM	RETAIL	A1 PRICE
GLM 90180	91 60526T	$85.70	$65.00

PINION NUT ADAPTOR KIT Holds pinion nut when removing pinion gear and drive shaft on MC-I, R-MR, and Alpha One drive units. Comes with one GLM 107-90220 drive shaft adapter.
PART NUMBER	OEM	RETAIL	A1 PRICE
GLM 90210	91 61067A3	$156.20	$133.00

BEARING CARRIER RETAINER WRENCH Removes and installs bearing carrier retainer nuts on Bravo One and Two, MC-I, R-MR, and Alpha One, Gen. Two, and TRS drive units.
PART NUMBER	OEM	RETAIL	A1 PRICE
GLM 90190	91 61069T	$71.85	$54.00

HINGE PIN TOOL Removes and installs hinge pins from all Mercruiser drive units.
PART NUMBER	OEM	RETAIL	A1 PRICE
GLM 90200	91 78310	$16.65	$15.00

PROP SHAFT ADAPTOR Provides a wrench surface to turn the propeller shaft on MC-I, R-MR, Alpha One; Alpha One, Gen. Two, Bravo One, and TRS drive units.
PART NUMBER	OEM	RETAIL	A1 PRICE
GLM 90230	91 61077	$28.95	$25.00

SHIFT CABLE TOOL Installs and removes shift cables on MC-I, R-MR, Alpha One; and Alpha One, Gen. Two drive units.
PART NUMBER	OEM	RETAIL	A1 PRICE
GLM 90110	91 12037	$27.40	$21.00

BEARING RETAINER WRENCH Installs and removes drive shaft bearing retainer on MC-I, R-MR, Blackhawk, all Bravo, and all Alpha drive units.
PART NUMBER	OEM	RETAIL	A1 PRICE
GLM 90100	91 17256	$73.10	$55.00

SHIFT SHAFT BUSHING TOOL Removes and installs the shift shat bushing in the gear case of MC-I, R-MR, and Alpha One drive units.
PART NUMBER	OEM	RETAIL	A1 PRICE
GLM 90140	91 31107T	$18.50	$14.00

PINION GEAR SHIMMING TOOL Measures pinion height of MC-I, R-MR, Alpha One, and Alpha One Gen.Two drive units.
PART NUMBER	OEM	RETAIL	A1 PRICE
GLM 90160	91 56048T	$175.30	$132.00

DRIVE SHAFT ADAPTOR Provides a wrench surface to turn the drive shaft on MC-I, R-MR, Alpha One, and Alpha One Gen. Two drive units.
PART NUMBER	OEM	RETAIL	A1 PRICE
GLM 90220	91 56775T	$22.35	$17.00

DRIVE GEAR SHIMMING TOOL Measures upper drive gear clearance on MC-I, R-MR, Alpha One, and Alpha One Gen. Two drive units.
PART NUMBER	OEM	RETAIL	A1 PRICE
GLM 90170	91 60523	$59.35	$45.00